Server in Level of RAID 0, RAID 1, RAID 5, RAID 10 Explained with Diagrams

RAID 0, RAID 1, RAID 5, RAID 10 Explained with Diagrams

This article is about the data storage technology. For other uses, see Raid (disambiguation).

RAID (originally redundant array of inexpensive disks, now commonly redundant array of independent disks) is a data storage virtualization technology that combines multiple physical disk drive components into a single logical unit for the purposes of data redundancy, performance improvement, or both.^[1]
Data is distributed across the drives in one of several ways, referred to as RAID levels, depending on the required level of redundancy and performance. The different schemas, or data distribution layouts, are named by the word RAID followed by a number, for example RAID 0 or RAID 1. Each schema, or a RAID level, provides a different balance among the key goals: reliability, availability, performance, and capacity. RAID levels greater than RAID 0 provide protection against unrecoverable sector read errors, as well as against failures of whole physical drives.

RAID 0, RAID 1, RAID 5, RAID 10 Explained with Diagrams

by Meghraj

 

RAID stands for Redundant Array of Inexpensive (Independent) Disks.
On most situations you will be using one of the following four levels of RAIDs.

• RAID 0
• RAID 1
• RAID 5
• RAID 10 (also known as RAID 1+0)

This article explains the main difference between these raid levels along with an easy to understand diagram.

In all the diagrams mentioned below:

• A, B, C, D, E and F – represents blocks
• p1, p2, and p3 – represents parity

RAID LEVEL 0

Following are the key points to remember for RAID level 0.

• Minimum 2 disks.
• Excellent performance ( as blocks are striped ).
• No redundancy ( no mirror, no parity ).
• Don’t use this for any critical system.

RAID LEVEL 1

Following are the key points to remember for RAID level 1.

• Minimum 2 disks.
• Good performance ( no striping. no parity ).
• Excellent redundancy ( as blocks are mirrored ).

RAID LEVEL 5

Following are the key points to remember for RAID level 5.

• Minimum 3 disks.
• Good performance ( as blocks are striped ).
• Good redundancy ( distributed parity ).
• Best cost effective option providing both performance and redundancy. Use this for DB that is
•  heavily read oriented. Write operations will be slow.

RAID LEVEL 10

Standard levels

Main article: Standard RAID levels

Storage servers with 24 hard disk drives and built-in hardware RAID controllers supporting various RAID levels.

A number of standard schemes have evolved. These are called levels. Originally, there were five RAID levels, but many variations have evolved, notably several nested levels and many non-standard levels (mostly proprietary). RAID levels and their associated data formats are standardized by the Storage Networking Industry Association (SNIA) in the Common RAID Disk Drive Format (DDF) standard:

RAID 0

RAID 0 consists of striping, without mirroring or parity. The capacity of a RAID 0 volume is the sum of the capacities of the disks in the set, the same as with a spanned volume. There is no added redundancy for handling disk failures, just as with a spanned volume. Thus, failure of one disk causes the loss of the entire RAID 0 volume, with reduced possibilities of data recovery when compared to a broken spanned volume. Striping distributes the contents of files roughly equally among all disks in the set, which makes concurrent read or write operations on the multiple disks almost inevitable and results in performance improvements. The concurrent operations make the throughput of most read and write operations equal to the throughput of one disk multiplied by the number of disks. Increased throughput is the big benefit of RAID 0 versus spanned volume.

RAID 1

RAID 1 consists of data mirroring, without parity or striping. Data is written identically to two (or more) drives, thereby producing a "mirrored set" of drives. Thus, any read request can be serviced by any drive in the set. If a request is broadcast to every drive in the set, it can be serviced by the drive that accesses the data first (depending on its seek time and rotational latency), improving performance. Sustained read throughput, if the controller or software is optimized for it, approaches the sum of throughputs of every drive in the set, just as for RAID 0. Actual read throughput of most RAID 1 implementations is slower than the fastest drive. Write throughput is always slower because every drive must be updated, and the slowest drive limits the write performance. The array continues to operate as long as at least one drive is functioning^.

RAID 2

RAID 2 consists of bit-level striping with dedicated Hamming-code parity. All disk spindle rotation is synchronized and data is striped such that each sequential bit is on a different drive. Hamming-code parity is calculated across corresponding bits and stored on at least one parity drive.This level is of historical significance only; although it was used on some early machines (for example, the Thinking Machines CM-2), as of 2014 it is not used by any of the commercially available systems.

RAID 3

RAID 3 consists of byte-level striping with dedicated parity. All disk spindle rotation is synchronized and data is striped such that each sequential byte is on a different drive. Parity is calculated across corresponding bytes and stored on a dedicated parity drive. Although implementations exist, RAID 3 is not commonly used in practice.

RAID 4

RAID 4 consists of block-level striping with dedicated parity. This level was previously used by NetApp, but has now been largely replaced by a proprietary implementation of RAID 4 with two parity disks, called RAID-DP. The main advantage of RAID 4 over RAID 2 and 3 is I/O parallelism: in RAID 2 and 3, a single read/write I/O operation requires reading the whole group of data drives, while in RAID 4 one I/O read/write operation does not have to spread across all data drives. As a result, more I/O operations can be executed in parallel, improving the performance of small transfers.

RAID 5

RAID 5 consists of block-level striping with distributed parity. Unlike RAID 4, parity information is distributed among the drives, requiring all drives but one to be present to operate. Upon failure of a single drive, subsequent reads can be calculated from the distributed parity such that no data is lost. RAID 5 requires at least three disks. RAID 5 is seriously affected by the general trends regarding array rebuild time and the chance of drive failure during rebuild. Rebuilding an array requires reading all data from all disks, opening a chance for a second drive failure and the loss of the entire array. In August 2012, Dell posted an advisory against the use of RAID 5 in any configuration on Dell EqualLogic arrays and RAID 50 with "Class 2 7200 RPM drives of 1 TB and higher capacity" for business-critical data.

RAID 6

RAID 6 consists of block-level striping with double distributed parity. Double parity provides fault tolerance up to two failed drives. This makes larger RAID groups more practical, especially for high-availability systems, as large-capacity drives take longer to restore. RAID 6 requires a minimum of four disks. As with RAID 5, a single drive failure results in reduced performance of the entire array until the failed drive has been replaced. With a RAID 6 array, using drives from multiple sources and manufacturers, it is possible to mitigate most of the problems associated with RAID 5. The larger the drive capacities and the larger the array size, the more important it becomes to choose RAID 6 instead of RAID 5. RAID 10 also minimizes these problems^.

RAID 10 (Striping + Mirroring):

RAID 10 combines the mirroring of RAID 1 with the striping of RAID 0. Or in other words, it combines the redundancy of RAID 1 with the increased performance of RAID 0. It is best suitable for environments where both high performance and security is required.

Minimum number of disks: 4
Pros: Very high performance. Fault tolerance.
Cons: Lower usable capacity/High cost. Limited scalability
Ideal use: Highly utilized database servers/ servers performing a lot of write operations.

See more details on our dedicated server hardware.
What is important to add is that even though some RAID levels provide data redundancy, it is never to be used as backup of your critical files. RAID protects you against hardware failure, but it does not protect you against errors, file corruption or malicious activity. Always store a complete and recoverable copy of your critical data on a separate hard drive (contact us for back up solutions). If you’re still not sure on which RAID is best for you and your application, send a message to our technical team and they will be happy to assist you with choosing the right solution.